How To Use A Micrometer Step By Step

Read the main scale reading at the edge of the thimble. Once you have the light on, you need to adjust the diaphragm control to the largest hole to let the most amount of light in.

Vernier, Depth Gauge, Micrometer, Caliper Depth gauge

With your right hand, using your pinky finger and the finger next to it, grip the frame with the front of the micrometer facing you.

How to use a micrometer step by step. Use the ratchet to tighten the spindle against a standard then lock the spindle. A micrometer is an essential tool for taking precise measurements. It has a precision of 0.01 mm and if you ever aspire to make something with tight tolerance you will probably need to use it.

It is precisely machined and can measure the. Used to check the elevation difference between two joints and also used to check the height of crush pins, diaphragm springs, welds and diaphragm pins. Your micrometer should come with a small wrench, this is used to adjust the zero position of the sleeve to match the thimble.

However, some microscopes use mirrors to reflect natural light, so that an electric outlet isnt necessary. Once you have identified the proper height gauge, the next step is to set up your gage block. Then, close the jaws of the instrument all the way so you start with your scales lined up at zero.

Slightly place the item to be measured against the anvil of the digital micrometer. To use a vernier caliper, start by twisting the locking screw counterclockwise to loosen it. To read the micrometer in thousandths, multiply the number of vertical divisions visible on the sleeve by 0.025, and to this add the number of thousandths indicated by the line on the thimble which best coincides with the central long line on the sleeve.

Comes with a bridge block, wrench and one 1 micrometer head. There is a tiny hole at the rear of the sleeve, this is to engage the wrench to. Look at the image above, you will see a number 5 to the immediate left of the thimble.

Then turn the ratchet until it starts to click for careful tightening as shown in the above diagram. Cut two smaller lengths to form two compartments. To obtain the first part of the measurement:

In this case, the reading on the main scale is 4.5 mm. First sand and then use some varnish to cover the filled area. Carefully open the jaws of the digital outside micrometer by revolving the ratchet.

It is a type of caliper that can measure the depth, length and thickness of any object that will fit into it. Place the object between anvil and spindle, and turn the thimble until the anvil and spindle grip the object. Check the proper height gauge that you need to check your inside micrometer accurately.

When you have determined which rod to use and have attached it to the end of the micrometer, turn the thimble until the micrometer reads zero. Make sure the micrometer is perpendicular to the surfaces being measured. These will store the micrometer spanners and gauges.

How to read a micrometer graduated in 0.001 This grip allows you to hold the micrometer upright and enables you to spin the spindle using your pointer finger and thumb. In a micrometer, the object you wish to measure is clamped between the anvil (the stationary end of the clamp) and the spindle (the moving part of the clamp).

A micrometer screw gauge uses a spindle that is moved by turning a small screw. Allow for the glue to dry and remove any excess. Use glue and saw dust to form filling for the plywood gaps.

Remove the gage block from the height gauge. Notice that there is an extra line below the datum line, this represents an additional 0.5 mm. Place the height gauge on a surface plate together with your gage block.

The above image shows a typical micrometer screw gauge and how to read it. A micrometer is a small tool that is used for measuring short distances accurately. Once the object is secured in the clamp, you use the numbering system on the thimble (the handle portion) to find your measurement.

Mitutoyo 117101 ACM25 Anvil Step Micrometer w/ Case 0